Huayang Co., Ltd.
+86(0)13926850059

红古Common Surface Issues on Silicone Parts and How They Are Prevented

2026/11/18   |   Read: 58

Surface defects are one of the most common quality questions raised about molded silicone parts. On a finished piece, a streak, dark line, pale patch, small bubble or rough edge stands out quickly even when the shape and size are correct. Most of these issues fall back to material, mold or handling rather than the silicone itself, and separating the source makes prevention and inspection far easier.

Molded silicone grip strength ring

Dark lines and uneven coloring often come from uneven pigment mixing, residue carried over from a previous run, or a mold cavity that has not been cleaned between colors. If pigment is not blended evenly through the base material, the batch can show streaks or patches; if a dark color remains in the cavity or runner, it can mark the next lighter run. Prevention here starts with controlled color mixing and a clean mold before each color change, so a fresh batch does not pick up leftover material from the last production run.

Sticking or tearing along the edge usually points to a worn mold surface, inadequate release or a demolding step that pulled too early. A mold cavity that is scratched or dull can hold the part, and an edge that tears on release leaves a rough flash or a missing corner. Checking mold condition, release treatment and cure timing helps reduce this type of damage, and parts should not be pulled from the cavity before the material has set enough to hold its shape.

Air pockets show up as small bubbles under the surface, and they are usually tied to the pouring or molding pressure and the cure conditions. Where air is trapped while material fills the cavity, it can leave a round mark that does not press out afterward. Adjusting how the material enters the cavity, pressure and cure temperature lowers the chance of trapped air, and inspecting the face right after demolding catches bubble-affected units before they move into finishing.

Surface dust or fiber marks usually appear after demolding, when parts are handled on a dirty bench, set down on loose fabric, or wiped with a cloth that sheds. These marks are often the result of the working environment rather than the mold itself. Keeping the inspection and packing area clean, using lint-free wiping material and handling parts on a clean surface reduces fiber and dust picking up on the still-soft or tacky surface.

Prevention in practice starts with clean molds and controlled color mixing, followed by consistent cure temperature and pressure. Parts should be inspected right after demolding so a bad batch can be isolated early instead of moving into packaging. When a recurring defect appears, keeping the sample along with the run parameters makes it easier to trace whether the cause is material, tooling or process. For buyers placing custom orders, asking to see sample inspection points and how defect types are separated gives a clearer picture of the supplier's quality routine, and the approved sample should be retained to compare later production runs against.

For inquiries or quotations about silicone rubber products, please contact us below.

We also accept inquiries by phone

TEL: +86(0)13926850059 * Mon - Fri 8:00 - 17:00

Mail: zwei@hwako.hk

侵 权 告 知 函

尊敬的用户您好,贵公司网站(silicone-hy.com)正在使用本公司拥有合法著作权的软件云优城市分站管理系统(简称“云优CMS”(中国国家版权局计算机软件著作权登记号:2018SR118857),但本公司的正版用户数据库中并未有贵公司的购买记录。

本公司《使用协议》已载明,企业用户(泛指非自然人的团体,如企业、协会等组织机构)必须购买软件授权后方可正式建站使用,在未获得商业授权之前,企业用户不得将本软件用于正式建站。根据上述内容,贵公司作为企业用户,如使用本公司开发的云优城市分站管理系统,则应通过购买方式获得本公司商业授权后方可使用。但截至本通知发出之日,贵公司尚未向本公司购买云优城市分站管理系统。故,贵公司的上述非法使用行为已严重侵犯本公司的计算机软件著作权,并给本公司造成了严重的经济损失。