Huayang Co., Ltd.
+86(0)13926850059

Silicone rubber products appear defective reasons

2023/01/08   |   Read: 5375

These years silicone rubber products are gradually accepted by consumers, which for silicone rubber manufacturers, the production process has become an important factor for customers to choose silicone friends, if silicone products are not confirmed in the early stage of development, how to let customers accept it? Therefore, for the silicone rubber production process, the bad problems that will occur before the manufacture of silicone products, what do you need to know to take preventive measures?


First, the reason for the fog surface of silicone rubber products:


1. Molding vulcanization time is too short leading to immature fog surface;


2. The mixing temperature of the mixer is too high, the air is humid and the humidity is too large;


3. The mixing compound is not uniform for a long time, resulting in the vulcanization agent being completely dispersed;


4. The speed at which molding workers place raw materials can't keep up with the temperature of the machine, resulting in foggy surface of the product;


Second, the product defects caused by the forming machine:


1. Different thickness of raw materials leads to immature products, adjust mold pressure and increase temperature;


2. When silica gel products are manufactured, there is internal wind, maintain a certain time, maintain a uniform number of vulcanization, maintain a certain temperature of the mold, and you can use an air gun to blow the mold to dissipate heat;


3. The product appears outsourcing wind, the vulcanization time is extended, the temperature is raised, and the die pad is replaced;


4, frequently appear all kinds of bad, you can remove the mold, the mold pad on the machine template cardboard and silicone mold pad;


Third, mold caused by poor products:


1, mold sticky impurities caused by adverse phenomena, you can use kerosene to wipe the mold with cloth;


2, the mold is bruised, with different degrees of sandblasting machine to choose different sand for spraying;


3, silica gel mold sticking phenomenon, spray stripping water to keep the product normal stripping, long-term spraying will lead to mold fog surface, so normal spraying can be;


Four, the machine trapped gas problem:


Room temperature vulcanized silica gel trapped gas will cause a lot of confusion in production, mainly related to the mold, so the mold design should consider the problem of exhaust:


1. Exhaust frequency is not enough;


2. Room temperature vulcanized silica gel mold is unreasonable, and exhaust tank is added;


3. Secondary exhaust for appropriate products;


4. Spray a small amount of release agent.


For inquiries or quotations about silicone rubber products, please contact us below.

We also accept inquiries by phone

TEL: +86(0)13926850059 * Mon - Fri 8:00 - 17:00

Mail: zwei@hwako.hk

侵 权 告 知 函

尊敬的用户您好,贵公司网站(silicone-hy.com)正在使用本公司拥有合法著作权的软件云优城市分站管理系统(简称“云优CMS”(中国国家版权局计算机软件著作权登记号:2018SR118857),但本公司的正版用户数据库中并未有贵公司的购买记录。

本公司《使用协议》已载明,企业用户(泛指非自然人的团体,如企业、协会等组织机构)必须购买软件授权后方可正式建站使用,在未获得商业授权之前,企业用户不得将本软件用于正式建站。根据上述内容,贵公司作为企业用户,如使用本公司开发的云优城市分站管理系统,则应通过购买方式获得本公司商业授权后方可使用。但截至本通知发出之日,贵公司尚未向本公司购买云优城市分站管理系统。故,贵公司的上述非法使用行为已严重侵犯本公司的计算机软件著作权,并给本公司造成了严重的经济损失。